Adsorption Efficiency Research Articles

Hydrogen-rich syngas upgrading via CO2 adsorption by amine-functionalized Cu-BTC: the effect of different amines.

Syngas produced from supercritical water gasification typically contain a high amount of CO2 along with H2. In order to improve the quality of syngas, amine-functionalized copper benzene-1,3,5-tricarboxylate (Cu-BTC) was synthesized as an effective adsorbent for selective removal of CO2 from syngas to increase the concentration of H2. The amines used in this study included monoethanolamine (MEA), ethylenediamine (EDA), and polyethyleneimine (PEI). The fundamental physicochemical character of adsorbents, CO2 adsorption capacity, and CO2/H2 selectivity were analyzed. The physicochemical characterization indicated that the structure of amine-functionalized Cu-BTC was partially damaged, which resulted in a decrease in specific surface area and pore volume. On the other hand, the enlarged pore size was beneficial for the mass transfer of gas in the adsorbent. Among these adsorbents, Cu-BTC/PEI exhibited the maximum CO2 adsorption capacity of 3.83mmol/g and the highest CO2/H2 selectivity of 19.74. It was found that the adsorption pressure is the most significant factor for the CO2 adsorption capacity. Lower temperature and higher pressure were favored for CO2 adsorption capacity and CO2/H2 selectivity, so physical adsorption by Cu-BTC played a dominant role. Moreover, Cu-BTC/PEI can be well-regenerated with stable adsorption efficiency after five consecutive cycles. These findings suggested that Cu-BTC/PEI could be a promising alternative adsorbent for CO2 capture from syngas.

Balancing the Kinetic and Thermodynamic Synergetic Effect of Doped Carbon Molecular Sieves for Selective Separation of C2H4/C2H6.

Selective separation of ethylene and ethane (C2H4/C2H6) is a formidable challenge due to their close molecular size and boiling point. Compared to industry-used cryogenic distillation, adsorption separation would offer a more energy-efficient solution when an efficient adsorbent is available. Herein, a class of C2H4/C2H6 separation adsorbents, doped carbon molecular sieves (d-CMSs) is reported which are prepared from the polymerization and subsequent carbonization of resorcinol, m-phenylenediamine, and formaldehyde in ethanol solution. The study demonstrated that the polymer precursor themselves can be a versatile platform for modifying the pore structure and surface functional groups of their derived d-CMSs. The high proportion of pores centered at 3.5Å in d-CMSs contributes significantly to achieving a superior kinetic selectivity of 205 for C2H4/C2H6 separation. The generated pyrrolic-N and pyridinic-N functional sites in d-CMSs contribute to a remarkable elevation of Henry selectivity to 135 due to the enhancement of the surface polarity in d-CMSs. By balancing the synergistic effects of kinetics and thermodynamics, d-CMSs achieve efficient separation of C2H4/C2H6. Polymer-grade C2H4 of 99.71% purity can be achieved with 75% recovery using the devised d-CMSs as reflected in a two-bed vacuum swing adsorption simulation.

Carbamazepine adsorption with a series of organoclays: removal and toxicity analyses

Organoclays have been used as efficient adsorbents for pharmaceutical pollutants present in waters. Carbamazepine (CBZ) is one of the drugs most frequently found in water bodies. In this study, four organoclays were prepared by modifying bentonite with the cationic surfactants hexadecyltrimethylammonium bromide (HDTMA) and octadecyltrimethylammonium bromide. The synthesized materials were characterized by XRD, CHN, FTIR, TG, BET and SEM analyses, confirming organophilization. The surfactants were interspersed in different arrangements in the interlayer space. CBZ sorption was investigated through batch equilibrium experiments, under variation of the pH, contact time, dosage of adsorbent, and initial drug concentration. Changes in pH showed no adsorption influence. CBZ sorption by the organoclays followed a pseudo-second-order kinetics. The best sorption performance was obtained for the BCN1-HDTMA100 clay, with a capacity of 34.34 ± 1.41 mg g−1, about ten times greater than the unmodified bentonite under the same conditions. This may be attributed to the higher surfactant content. The adsorption isotherm at 25 ºC showed linear behavior. Toxicity tests of the organoclays and corresponding medium in presence of CBZ were carried out. This is a novelty report. Most of the organoclays had no toxicity against Artemia salina. The toxicity of the medium after adsorptive treatment was eliminated. Organoclay-CBZ hybrids were also characterized after adsorption. FTIR and TG analyzes confirmed the incorporation of the drug. Hydrophobic interaction was the dominant contribution evaluated to the adsorption of CBZ. The results demonstrated that organoclays can be a promising alternative adsorbent for the removal of pharmaceutical pollutants in water remediation.

Comparison of MAF-32 and a One-Pot Synthesized Superparamagnetic Iron Oxide/MAF-32 Composite for the Adsorption of Diclofenac

The global presence of pharmaceutical pollutants in water sources represents a burgeoning public health concern. Recent studies underscore the urgency of addressing this class of emerging contaminants. In this context, our work focuses on synthesizing a composite material, FexOy/MAF-32, through a streamlined one-pot reaction process, as an adsorbent for diclofenac, an emerging environmental contaminant frequently found in freshwater environments and linked to potential toxicity towards several organisms such as fish and mussels. A thorough characterization was performed to elucidate the structural composition of the composite. The material presents magnetic properties attributed to its superparamagnetic behavior, which facilitates the recovery efficiency of the composite post-diclofenac adsorption. Our study further involves a comparative analysis between the FexOy/MAF-32 and a non-magnetic counterpart, comprised solely of 2-ethylimidazolate zinc polymer. This comparison aims to discern the relative advantages and disadvantages of incorporating magnetic iron oxide nanoparticles in the contaminant removal process facilitated by a coordination polymer. Our findings reveal that even a minimal incorporation of iron oxide nanoparticles substantially enhanced the composite’s overall performance in pollutant adsorption.

Preparation and Adsorption Performance of Boron Adsorbents Derived from Modified Waste Feathers

This research focuses on modifying discarded feathers by grafting glycidyl methacrylate (GMA) onto their surface through thiolation, followed by an epoxy ring-opening reaction with N-methyl-D-glucamine (NMDG) to synthesize feather-based boron adsorbents. Optimization of the adsorbent preparation conditions was achieved through single-factor experiments, varying temperature, time, GMA concentration, and initiator dosage. The synthesized adsorbent (F-g-GMA-NMDG) underwent characterization using Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The adsorption behavior of the adsorbent was studied, and its boron adsorption capacity at different temperatures was determined through static adsorption kinetic curves. Analysis of adsorption isotherms, kinetics, and thermodynamics was conducted. Results indicate that the boron adsorption process by F-g-GMA-NMDG follows a pseudo-second-order model. The adsorption process is endothermic, with higher temperatures promoting adsorption efficiency. Gibbs free energy (ΔG) confirms the spontaneity of the adsorption process. Enhanced adsorption efficacy was observed under neutral and acidic pH conditions. After four cycles, the adsorbent maintained its adsorption efficiency, demonstrating its stability and potential for reuse. This study provides novel insights into both the treatment of discarded feathers and the development of boron adsorbents.

Enhanced adsorption and removal of Cd(II) from aqueous solution by amino-functionalized ZIF-8

Zeolite imidazolate framework-8 (ZIF-8), which is a special subgroup of metal–organic frameworks (MOFs), was synthesized and modified by ethylenediamine (ZIF-8-EDA) to prepare an efficient adsorbent for the high sorption of Cd2+ ions from solution. The synthesized and modified ZIF-8 (ZIF-8-EDA) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, Brunauer–Emmett–Teller (BET), field emission scanning electron microscopy (FE-SEM) with energy dispersive spectroscopy (EDS), and transmission electron microscopy (TEM) analysis. The optimum conditions for dosage of adsorbent, initial ion concentration, pH, and contact time were 0.05 g/l, 50 mg/l, 6, and 60 min, respectively, for cadmium ion sorption from aqueous solutions with a removal efficiency of 89.7% for ZIF-8 and 93.5% for ZIF-8-EDA. Adsorption kinetics and equilibrium data were analyzed using the Langmuir and Freundlich equations. The Langmuir model fitted the equilibrium data better than the Freundlich model. According to the Langmuir equation, the maximum uptake for the cadmium ions was 294.11(mg/g). The calculated thermodynamic parameters (ΔG°, ΔH°, and ΔS°) indicated that the adsorption process was feasible, spontaneous, and endothermic at 20–50 °C. Based on the results, the amino functionalized ZIF-8 had improved adsorption performance due to the replacing of the starting linker with organic ligands that had effective functional groups, leading to chemical coordination due to the interaction of metal ions with the non-bonding pair of electrons on the N atoms of the amino functional group. The selectivity toward metal ion adsorption by ZIF-8-EDA was Cd2+ > Pb2+ > Ni2+‏.

Efficient wastewater decontamination using magnetic bentonite-alginate beads: A comprehensive study of adsorption dynamics, regeneration, and molecular interactions

This study enhances wastewater treatment methodologies by developing magnetic bentonite-alginate beads (MBent-A beads) for adsorbing methylene blue (MB) from aqueous solutions. Experimental and computational analyses were employed to evaluate the beads' adsorption efficiency, utilizing characterization techniques including Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), point of zero charge (pHpzc), Brunauer-Emmett-Teller method (BET), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) to examine the composite’s morphology and chemistry. Findings reveal a significant adsorption capacity with the beads' specific surface area at 3.94 m2/g and a maximum adsorption capacity of 774.32 mg/g. Adsorption kinetics adhered closely to the pseudo-second-order model, indicating a rapid adsorption process, while Langmuir isotherm analysis confirmed a uniform monolayer adsorption and temperature-dependent capacities. Thermodynamic analysis showed the adsorption process to be spontaneous and exothermic, reflecting a strong affinity between MB molecules and the bead surface. The beads demonstrated durability with more than 90% removal efficiency after five regeneration cycles, highlighting a minimal decrease from 98.54% to 90.60%. In-depth theoretical investigations using density functional theory (DFT), frontier molecular orbital (FMO), reduced density gradient (RDG), and quantum theory of atoms in molecules (QTAIM) analyses identified van der Waals forces and hydrogen bonding as primary interactions driving the adsorption. The synthesis of MBent-A beads and their confirmed efficacy in dye adsorption integrates experimental research with theoretical modeling, offering a robust solution for treating dye-contaminated wastewater and underlining the potential of MBent-A beads in environmental remediation.

Construction of a Multiscaled Synergistic Membrane for Efficient Dye Adsorption and Emulsion Separation

Construction of a Multiscaled Synergistic Membrane for Efficient Dye Adsorption and Emulsion Separation

Fabrication of melamine formaldehyde/graphene oxide composite for efficient static and dynamic adsorption of lead ions from aqueous medium.

The present work discusses the synthesis, characterization, and environmental applications of graphene oxide (GO), melamine formaldehyde resin (MF), and melamine formaldehyde/graphene oxide composite (MGO) for the efficient removal of Pb2+ from aqueous medium via batch and column procedures. TGA, XRD, TEM, zeta potential, nitrogen adsorption/desorption, ATR-FTIR, and other characterization techniques revealed that MGO is characterized by a greater surface area (609 m2/g), total pore volume (1.0106 cm3/g), pHPZC (6.5), and the presence of various surface chemical functional groups. The synthesized solid adsorbents were used in both static and dynamic adsorption processes to remove Pb2+, with varying application parameters such as pH, starting concentration, adsorbent dosage, and shaking time in the case of static adsorption method. While through the column adsorption process the effects of column bed height, flow rate, and starting Pb2+ were taken into consideration. Results of the batch adsorption demonstrated that MGO had the highest Langmuir adsorption capacity (201.5 mg/g), and the adsorption fit the nonlinear Langmuir adsorption model and Elovich kinetic models. The adsorption of Pb2+ onto all prepared solid materials is endothermic, spontaneous, and physical in nature, as demonstrated by thermodynamic studies. Column adsorption of Pb2+ well fitted by Thomas and Yoon Nelson nonlinear adsorption models. MGO showed a maximum column adsorption capacity of 168 mg/g when applying 4 cm, 15 mL/min, and 150 mg/L as bed height, flow rate, and initial Pb2+, respectively. With only a 12.6% reduction in its adsorption capacity, column regeneration showed that MGO exhibited a high degree of reusability even after five cycles of adsorption/desorption studies.

Polyaniline/reduced graphene oxide doping induced abundant active sites in enset fiber as an efficient adsorbent material for wastewater treatment

Polyaniline/reduced graphene oxide doping induced abundant active sites in enset fiber as an efficient adsorbent material for wastewater treatment

Unleashing the potential of Cajanus cajun biochar polymer composite for Cu (II) removal: mechanism, modification, and application.

This study introduces a cost-effective approach to fabricating a porous and ionically surface-modified biochar-based alginate polymer networks composite (SBPC) through air drying. The study critically analyzes the role and concentrations of various components in the success of SBPC. Characterization techniques were employed to evaluate the microstructure and adsorption mechanism, confirming the ability of the adsorbent's carboxyl and hydroxyl groups to eliminate various heavy metal ions in water simultaneously. The SBPC demonstrated high copper binding capacities (937.4mg/g and 823.2mg/g) through response surface methodology (RSM) and column studies. It was also influential in single and natural systems, exhibiting competitive behavior and efficient removal of Cu2+. The Langmuir isotherm and pseudo-second-order kinetics strongly correlate with experimental data, with R2 values of 0.98 and 0.99, respectively. SBPC showed remarkable stability, up to 10 desorption cycles, and achieved 98% Cu2+ adsorption efficiency and 91.0% desorption. Finally, the cost analysis showed a cost of 125.68 INR/kg or 1.51 USD/kg, which is very low compared to the literature. These results highlight the potential of SPBC and show that it provides an efficient and cost-effective solution for removing Cu2+ from a real system.

Effects of different precursors on the structure of lignin-based biochar and its ability to adsorb benzopyrene from sesame oil

Agricultural by-products of sesame are promising bioresources in food processing. This study extracted lignin from the by-products of sesame oil production, namely, the capsules and straw of black and white sesame. Using acid, alkali, and ethanol methods, 12 distinct lignins were obtained to prepare biochar, aiming to investigate both the structural characteristics of lignin-based biochar (LBB) and its ability to remove benzo[a]pyrene (BaP) from sesame oil. The results showed that white sesame straw was the most suitable raw material for preparing biochar. In terms of the preparation method, acid-extracted lignin biochar was more effective in removing BaP than alkaline or ethanol methods. Notably, WS-1LB (white sesame straw acid-extracted lignin biochar) exhibited the highest BaP adsorption efficiency (91.44 %) and the maximum specific surface area (1065.8187 m2/g), characterized by porous structures. The pseudo 2nd and Freundlich models were found to be the best fit for the adsorption kinetics and isotherms of BaP on LBB, respectively, suggesting that a multilayer adsorption process was dominant. The high adsorption of LBB mainly resulted from pore filling. This study provides an economical and highly efficient biochar adsorbent for the removal of BaP in oil.

Removal of Cr(VI) from Wastewater Using Acrylonitrile Grafted Cellulose Extracted from Sugarcane Bagasse

A highly efficient low-cost adsorbent was prepared using raw and chemically modified cellulose isolated from sugarcane bagasse for decontamination of Cr(VI) from wastewater. First, cellulose pulp was isolated from sugarcane bagasse by subjecting it to acid hydrolysis, alkaline hydrolysis and bleaching with sodium chlorate (NaClO3). Then, the bleached cellulose pulp was chemically modified with acrylonitrile monomer in the presence Fenton’s reagent (Fe+2/H2O2) to carry out grafting of acrylonitrile onto cellulose by atom transfer radical polymerization. The developed adsorbent (acrylonitrile grafted cellulose) was analyzed by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR). Both raw cellulose and acrylonitrile grafted cellulose were used for chromium removal from wastewater. The effects of metal ion concentration, pH, adsorbent dose and time were studied, and their values were optimized. The optimum conditions for the adsorption of Cr(VI) onto raw and chemically modified cellulose were: metal ion concentration: 50 ppm, adsorbent dose: 1 g, pH: 6, and time: 60 min. The maximum efficiencies of 73% and 94% and adsorption capacities of 125.95 mg/g and 267.93 mg/g were achieved for raw and acrylonitrile grafted cellulose, respectively. High removal efficiency was achieved, owing to high surface area of 79.92 m2/g and functional active binding cites on grafted cellulose. Isotherm and kinetics studies show that the experimental data were fully fitted by the Freundlich isotherm model and pseudo first-order model. The adsorbent (acrylonitrile grafted cellulose) was regenerated using three different types of regenerating reagents and reused thirty times, and there was negligible decrease (19%) in removal efficiency after using it for 30 times. Hence, it is anticipated that acrylonitrile could be utilized as potential candidate material for commercial scale Cr(VI) removal from wastewater.

Amine-impregnated natural inorganic nanotubes via layer-by-layer electrostatically self-assembly approach for efficient CO2 adsorption

Developing cost-effective and high-performance solid amine adsorbents has considered as an important way to alleviate the greenhouse effect. How to precisely regulate its pore structure and surface interface characteristics, and how to cooperate to optimize the dynamic mass transfer and adsorption–desorption behavior of gas in the adsorbent are still challenging work. Herein, we demonstrated a facile and efficient approach to construct polyethyleneimine (PEI) impregnated halloysite nanotubes (HNTs) as an emerging nanocomposite for CO2 capture. Based on the natural electrostatic differences of inner and outer walls for HNTs, the hollow tubular structures of adsorbents were constructed by selective surface modification and layer-by-layer electrostatic self-assembly technology to improve the CO2 uptake capacity and cyclic stability, in which poly(sodium-p-styrene sulfonate) (PSS) and PEI were used as polyanionic and polycationic layer, respectively, to coat the inner walls of HNTs. The loading capacity of PSS-PEI composite ionic layers in HNTs and the influence of PSS polyanionic layer on PEI dispersion were specifically discussed according to the CO2 uptake capacity, adsorption heat, thermodynamics and kinetics of the adsorbents. The optimal PEI20-0.5PHNTs adsorbent exhibited a higher CO2 uptake of 0.87 mmol/g at 80 °C in the flow of 40 vol% N2/60 vol% CO2 than that of PEI20-HNTs, owing to the high amine efficiency due to the uniform dispersion of PEI in the electrostatic composite ionic layers. Furthermore, PEI20-0.5PHNTs reached 75 % of the maximum adsorption capacity at the 5th min of the adsorption process and released the most heat during adsorption at − 18.28 kJ/mol due to the presence of electrostatic composite ionic layers. PEI20-0.5PHNTs showed excellent cyclic stability with a slight loss of 7.4 %. The electrostatic self-assembled adsorbent obtained by layer-by-layer loading of PSS and PEI based on the unique surface charge characteristics of HNTs is an inspiration for the synthesis of cost-effective solid amine adsorbents for practical CO2 capture and separation.

Mg–Fe Layered Double Hydroxides/Polyacrylonitrile Nanofibers for Solar-Light Induced Peroxymonosulfate Elimination of Tetracycline Hydrochloride

The photo-induced peroxymonosulfate (photo-PMS) reaction is a promising route to eliminate antibiotics from waste water. To achieve excellent photo-PMS activity in Mg–Fe layered double hydroxides (LDHs) for tetracycline hydrochloride (TCH) degradation under simulative solar-light irradiation, Mg–Fe LDHs-loaded polyacrylonitrile (Mg–Fe/PAN) nanofibers were in-situ prepared via the hydrothermal route. For comparison to the photocatalysis and photo-PMS process, the Mg–Fe/PAN-assisted photo-PMS process exhibited a better elimination activity for TCH elimination. In addition, the photo-PMS activities of Mg–Fe/PAN composites were greatly affected by Mg–Fe LDHs content, TCH concentration, pH, and inorganic salts. Among these Mg–Fe/PAN composites, the optimal MgFe2/PAN with a Mg/Fe molar ratio of 1:2 and a nominal Mg–Fe LDHs content of 2.0 wt. % removed 81.31% TCH solution of 80 mg L−1 TCH within 120 min. This enhanced photo-PMS capacity of MgFe2/PAN was ascribed to the abundant active sites formed by functional groups and oxygen defects for efficient TCH species adsorption and photon capturing, and the tight interface between Mg–Fe LDHs nanoparticles and PAN nanofibers for the rapid separation and transfer of photoinduced e−/h+ pairs. SO4•− and •O2− radicals were vital for the MgFe2/PAN-assisted photo-PMS reaction.

Greenly synthesised novel microporous ZnO/GO for adsorption of methyl orange and malachite green

ABSTRACT This study presents a greenly synthesised novel nanocomposite composed of Zinc Oxide (ZnO) and Graphene Oxide (GO) for the adsorption of dyes from aqueous solutions. The nanocomposite was synthesised using algae thus representing a green and eco-friendly method, ensuring minimal environmental impact. The physical characterisation of zinc oxide and graphene oxide nanocomposite (ZnO/GO) was done using X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy (FT-IR), Zeta Potential, and Particle Size Analyzer (PSA). The pore diameter of the ZnO/GO was 1.801 nm, and its total surface area was 54.062 m2/g. The nanocomposite’s adsorption performance was systematically investigated through batch adsorption experiments. With an adsorption efficiency of 296.73 mg/g and 259.74 mg/g for MO and MG, the Langmuir isotherm model outperforms the Freundlich isotherm model in terms of adsorption. The pseudo-second-order model having an R2 value of 0.99 for both MO and MG, offers a more convincing explanation of adsorption than the pseudo-first-order model. The results demonstrated rapid adsorption kinetics and high adsorption capacities for both cationic and anionic dyes. Additionally, the ZnO/GO has a high reusability without significant degradation. The sustainable nature of the nanocomposite was emphasised by its efficient dye removal, reusability, and minimal secondary waste generation.

Amino Group-Driven Adsorption of Sodium p-Perfluorous Nonenoxybenzene Sulfonate in Water by the Modified Graphene Oxide

Sodium p-perfluorous nonenoxybenzene sulfonate (OBS) is one of the key alternatives to perfluoroalkyl substances (PFASs). Its widespread tendency has increased extensive contamination in the aquatic environment. However, the present treatment technology for OBS exhibited insignificant adsorption capacity and long adsorption time. In this study, three proportions (1:5, 3:5, and 10:1) of chitosan-modified amino-driven graphene oxide (CS-GO) were innovated to strengthen the OBS adsorption capacity, compared with graphene oxide (GO) and graphene (GH). Through the characterization of SEM, BET, and FTIR, it was discovered that CS was synthetized on GO surfaces successfully with a low specific surface area. Subsequently, batch single influence factor studies on OBS removal from simulated wastewater were investigated. The optimum removal efficiency of OBS could be achieved up to 95.4% within 2 h when the adsorbent was selected as CS-GO (10:1), the dosage was 2 mg, and the pH was 3. The addition of inorganic ions could promote the adsorption efficiency of OBS. In addition, CS-GO presented the maximum adsorption energy due to additional functional groups of -NH3, and electrostatic interaction was the foremost motive for improving the adsorption efficiency of OBS. Moreover, OBS exhibited the fastest diffusion coefficient in the CS-GO-OBS solution, which is consistent with the fitting results of adsorption kinetics.

Adsorption dynamics of per- and polyfluoroalkyl substances (PFAS) on activated carbon: Interplay of surface chemistry and PFAS structural properties

Using activated carbon (AC) to adsorb per- and polyfluoroalkyl substances (PFAS) is highly practical for environmental remediation. However, examining the surface chemistry of carbonaceous material with regard to the removal of various PFAS has been limited, as the focus has often solely been on perfluorooctanoic acid and perfluorooctane sulfonic acid. Consequently, this study systematically explores the role of AC surface chemistry in the adsorption of PFAS with various structural properties using ACs that have been modified for different degrees of acidity, basicity, and hydrophobicity. Batch adsorption studies have demonstrated that the affinity of PFAS for the AC surface is negatively correlated with surface acidity. The removal performance at an adsorbent dose of 2 mg/L and an initial PFAS concentration of 600 ng/L is 27.4–91.4 %, 57.2–95.6 %, 92.4–99.2 %, and 89.1–99.6 % for an AC with an acidic surface, unmodified AC, defunctionalized AC, and AC with basic surface, respectively. Analyses of the adsorption isotherms, kinetics, and removal performance of the four types of ACs and 14 PFAS in water at different pH and ionic strengths reveal that hydrophobic, electron donor–acceptor, and electrostatic interactions, as well as negative charge-assisted hydrogen bond formation are necessary to describe the key adsorption characteristics observed in the experiments. The relative significance of the adsorption mechanisms depends on the PFAS structural properties, AC surface chemistry, and water composition. This extensive discourse contributes substantially to the design of an efficient carbonaceous adsorbent with specific surface moieties for removing PFAS from water.

Advanced Pyrene Copolymer/rGO Hydrogels for Efficient Congo Red Removal from Aqueous Systems

AbstractThis study investigates the use of hydrogel semi‐interpenetrating polymer networks (semi IPN) as efficient adsorbents for removing the dye congo red (CR) from aqueous solutions. Specifically, three hydrogel semi IPN, namely AH0–AH2, were synthesized through redox polymerization of acrylamide, polyethylenimine, polyhydroxylethylmethacrylate and (pyren‐1‐yl)methyl methacrylate/2‐acrylamido‐2‐methylpropane‐1‐sulfonic acid copolymer (pyrene−AMPS) using a reduced graphene oxide (RGO)‐N,N’‐methylene‐bis(acrylamide) (MBA)‐based crosslinker (GABC). Results indicated that these hydrogels were efficient in removing CR at pH 6.73, with the adsorption behaviour conforming to the Langmuir isotherm. This suggests a monolayer adsorption pattern, indicating a chemical nature. Thermodynamic analysis supports the practical feasibility of this process. The negative Gibbs free energy of adsorption (ΔG̊) indicates that adsorption is spontaneous and favorable. Conversely, the positive standard entropy of adsorption (ΔS̊) suggests an increase in molecular randomness during the process. Additionally, the standard enthalpy change (ΔH̊) suggests an endothermic activation energy for the binding process. Response Surface Methodology (RSM), utilizing four variables was employed to optimize the removal of CR. The model demonstrated high R2‐values and strong agreement between experimental and projected results, affirming its reliability. AH1 and AH2 showed significant efficacy in removing CR dye from aqueous solutions, underscoring their potential application in wastewater remediation.

Innovative optimization for maximum magnetic nanoparticles production by Trichoderma asperellum with evaluation of their antibacterial activity, and application in sustainable dye decolorization

A pioneer microbial-based synthesis of various nanoparticles is gaining more attention due to their potent applications in various industries. The magnetic nanoparticles (M-nps) were fabricated for the first-time using the cell free extract of Trichoderma asperellum. The M-nps bioprocess optimization was performed using Response Surface Methodology and Artificial Neural Network.The bioprocess was significantly (P < 0.05) affected by pH, stirring speed, and incubation period. The M-nps displayed a strong antibacterial efficiency against Escherichia coli, Pseudomonas aeruginosa, Bacillus subtilis, and Staphylococcus aureus in a dose-dependent manner. The minimum inhibitory concentration (MIC) for E. coli, P. aeruginosa, and S. aureus were respectively found to be 25.0, 6.25, and 3.125 µg/ml. While the minimum bactericidal concentration (MBC) was 25.0, 12.5, and 6.25 µg/ml. The highest inhibition zone of 22 mm was recorded for B. subtilis at 80 µg/ml with MIC and MBC of 3.125 µg/ml. The sodium alginate/M-nps microbeads was successfully prepared without any crosslinkers. The microbeads exhibited the highest adsorptive efficiency (84.32%) for malachite green at pH 8.0, dose 0.1 g, and time 60 min. The experimental data were superlative fitted to Langmuir’s isotherm, hinting monolayer adsorption of MG molecules with 117.65 mg g‐−1 adsorptive capacity. The regenerated beads continued up-to six consecutive cycles and maintained more than 90%, indicating the multiple time use of the prepared material. Hence, the green magnetic nanoparticles display promising application in combating bacterial pathogens. The magnetic microbeads can be employed as an alternative eco-friendly, highly efficient, sustainable, and low-cost biosorbent in removing contaminants from wastewater.